Product Features
The numbering of the product features refers to the diagram of the power tool on the graphics page.
|
(1) |
Guide groove for parallel guide |
(2) | Scale for spacing between saw blade and parallel guide |
(3) | Angle guide |
(4) | Recessed handles |
(5) | Guide groove for angle guide |
(6) | Protective cover |
(7) | Saw table |
(8) | Riving knife |
(9) | Anti-kickback pawlsA) |
(10) | Parallel guide |
(11) | V guide groove on the saw table for the parallel guide |
(12) | Mounting holes |
(13) | Carrying handle |
(14) | Saw table expansion |
(15) | Fixing clip for the GTA 600 saw stand |
(16) | Clamping handle for saw table expansion |
(17) | Locking lever for setting the bevel angle |
(18) | Hand wheel |
(19) | Crank for raising and lowering the saw blade |
(20) | On/off switch safety flap |
(21) | Hex key (2 mm) |
(22) | Hex key (5 mm) |
(23) | Ring spanner (23 mm) |
(24) | Push stick |
(25) | Adjusting screw for adjusting the clamping force of the parallel guide |
(26) | Table insert |
(27) | Saw blade |
(28) | Magnifying glass |
(29) | Profile rail |
(30) | Cable holder |
(31) | Holding clip for storing the additional parallel guide |
(32) | Chip ejector |
(33) | Dust extraction adapter |
(34) | Bracket for storing the protective cover |
(35) | Clamping lever for riving knife |
(36) | Hex socket screws for riving knifeA) |
(37) | Positioning pins for riving knife |
(38) | Recesses for table insert |
(39) | Clamping lever for protective cover |
(40) | Guide pin for protective cover |
(41) | Clamping handle for parallel guide |
(42) | V guide for parallel guide |
(43) | Additional parallel guide |
(44) | "Additional parallel guide" fastening set |
(45) | Guide rail for angle guide |
(46) | "Profile rail" fastening set |
(47) | Fastening screw for chip ejector |
(48) | Push buttons for retracting the guide bolt of the anti-kickback pawlsA) |
(49) | Clamping nut |
(50) | Spindle locking lever |
(51) | Clamping flange |
(52) | Tool spindle |
(53) | Mounting flange |
(54) | Angle indicator (vertical) |
(55) | Scale for bevel angles |
(56) | Locking knob for all mitre angles |
(57) | Angle indicator on the angle guide |
(58) | Saw table spacing indicator |
(59) | On button |
(60) | Knurled nut for profile rail |
(61) | Cross-head screw for setting the 0° stop |
(62) | Stop for 0° bevel angle |
(63) | Screw for bevel angle indicator |
(64) | Cross-head screw for setting the 45° stop |
(65) | Stop for 45° bevel angle |
(66) | Hex socket screws (5 mm) on the front for adjusting the parallelism of the saw blade |
(67) | Hex socket screws (5 mm) on the rear for adjusting the parallelism of the saw blade |
(68) | Screw for saw table spacing indicator |
(69) | Hex socket screws (5 mm) for adjusting the parallelism of the parallel guide |
(70) | Screw for parallel guide spacing indicator |
(71) | Adjusting screws for table insert |
(72) | Bracket for storing the "additional parallel guide" fastening set |
(73) | Holding clip for storing the dust extraction adapter |
(74) | Bracket for storing the anti-kickback pawlsA) |
(75) | Securing nut for the ring spanner and for hanging the push stick |
(76) | Bracket for storing the hex key |
(77) | Holding clip for storing the angle guide |
- A)
Country version 3 601 M30 5C2